Brand:REBOND
MOQ:1000
Quantity:10
1. Product Description
TP5300 Double Coated Tissue Tape for dimensional stability andimproved handling with ease of die cutting and laminating.The higntack adhesive provides relatively high initial adhesion and goodshear holding power to a variety of surfaces.
2. Construction
TP5306 | |
Face side 1 Adhesive Type/Thickness | Acrylate/0.003(0.076mm) |
Backside 2 Adhesive Type/Thickness | Acrylate/0.003(0.076mm) |
Liner Color,Type | White,120g PCK |
Liner Caliper | 0.0052(0.130mm) |
Carrier Type | Tissue |
Note 1:Faceside adhesive is on the interior of the roll,exposedwhen unwound. 2:Backside adhesive is on the exterior of theroll,exposed when liner is removed. | |
3. Typical Physical Note : Thefollowing technical information and data should beconsidered representative or typical only and should not be used forPropertiesand specificationpurposes.Performance Characteristics
TP 5306 | ||
Adhesion to stainless steel ASTM D3330-180 degree,2 mil PET 30 minute RT | 80(N/100mm) | |
Adhesion to AL ASTM D3330-180 degree,2 mil PET 30 minute RT | 80(N/100mm) | |
Adhesion to other surfaces ASTM D3330-180 degree, 2 mil PET,30 minutes RT Shear strength-ASTM D3654 | PCP :65 | |
ABS :80 | ||
(1 inch2 sample size)1000grams at 72(22) | 5000 minutes | |
Relative solvent resistance | Medium-Low | |
UV Resistance | Medium | |
Relative High Temperature | Operating Ranges | Long Term(days,week) 70 |
Short Term(minutes,hours)150 | ||
Shelf Life of Tape in Roll Form | 24 months from date of manufacture when stored inoriginal cartons at 70(21) and 50% relative humidity | |
4. Application Bond strength isdependent upon the amount ofadhesive-to-surfaceTechniques contactdeveloped. Firm application pressure helps develop better adhesivecontact and improves bond strength. To obtain optimumadhesion, the bonding surfaces must be clean,dry and well unified.Some typical surface cleaning solvents are isopropyl alcohol orheptane. Note: Carefully read and follow the manufacturersprecautions and directions for use when working withsolvents. Ideal tape application temperature range is 70°F to100°F (21°C to38°C). Initial tape application to surfaces attemperatures below 50°F (10°C) is not recommended because theadhesive becomes too firm to adhere readily. However, once properlyapplied, low temperature holding is generallysatisfactory. 5.General All tapes have a film carrier, which can adddimensional stability toInformation foams and other substrates. The carrier alsoprovides easier handling during slitting and die-cutting.
6.Features Adhesive is amedium-firm acrylic adhesive system featuring both high initialadhesion and good high temperature holding power.
7.Application Medical/non-medicaldiagnostic teststripsIdeas Plastic film lamination/bondingSplicingFoamlamination
8.Application To apply adhesives in awide web format, lamination equipmentisEquipment required to ensureacceptable quality. To learn more about working withpressure-sensitive adhesives please refer to technical bulletin,Lamination Techniques for Converters of LaminatingAdhesives. 9.Certification/ MSDS: has prepared a MSDS for theproducts.Recognition TSCA: The product are defined as articles under the ToxicSubstances Control Act and therefore,are exempt from inventorylisting requirements.
ISO9001 ISO14001 |
This Engineered Adhesives Division product was manufactured under a quality system registered to ISO 9001 standards andEnvironmental system registered to ISO 14001standards
HOT--TP5306: Double coated tissue tape(substitute for SokenA7900 and 3M55236)
