Model:CAH(11)-400D
CAH(11)—400D Step Punch Cut to Length Line Introduction
1. Single head decoiler
Coil ID: 500mm
Coil OD: 1200mm (Max.)
Coil weight: 1.5 T (Max.)
Decoiler speed: Adjust with feeder
Decoiler use synchronization stepless speed regulation with feeding, motoring.
2,Buffer pithead
the buffer pit is between the coiler and feeder, to make sure the material in free condition before crossing the sheet feeder .the buffer pit guaranteed by precise optical grating encode, that control the coiler revolving, slow down, cut-off and the coiler ‘s head braking; The feeder do not work when the feeder work fast and precise optical grating encode guarantee moving slow, to make sure the same feeding speed between the coiler and the feeder to avoid the material straightening or banking up in buffer pit.
3. Feeder machine
Make up of Up and down feeding roller and length measurement roller etc, feeder roller drive system adopt Taiwan DELTA drive motion control system. Center position, feeder can longitudinal whole translation; Double motor drive, using the most advanced servo push-pull institution; Encoder length measurement, servo loop control;
Feed roller adopts polyurethane, normal use 0-180 m/min, highest feeding speed of 240M/min.
4. V punch part
Mainly includes O punch 1 set, servo motor driver.
O punch has horizontal step function, according to the program to automatic adjust.
Punch range material center of ± 50 mm, stepping series can up to thirty –six levels.
V shear use Taiwan DELTA servo motor drive, high efficiency, have low noise.
Knife life: Each grinding can use at less 1 million times
5. Shearing part
Mainly make up of +90º shearing machines. And they were including hard alloy cutter 1 set.
Knife life: Each grinding can use at less 1 million times
6. Discharging platform
Unilateral positioning, transmission belt stepless speed regulation, discharging smoothly.
Discharging motor use Germany ABB motor, Toshiba inverter control.
7,Automatic Stack mechanism of slope
8,Pneumatic system
Double cylinder parallel sliding shear mode,
Each cylinder is provided with a special gas cylinders, and install a high-speed discharge valve .
9,Electric control system
The electric control system includes main electric control cabinet and work station.
u Main technical parameters
- Rang of work
Thickness: 0.23 - 0.35mm
Width: 40 - 440mm
Length: 40 to 1000mm
- Require for coil
Width tolerance: ±0.1mm
Burr≤0.03mm
S deviation between: 2000mm ≤0.2mm
- Precision
Length tolerance: ±0.2mm
Angle tolerance: ±0.025°
Burr≤0.02mm
4. Feeding speed: 150m/min
1) Knife life More than one million (Each grinding; Hard alloy material
2) Total installed capacity: about 10Kw
3) Total gas consumption: 0.2 M3/min
5. Working conditions
(1) Temperature less than 40°C
(2) Voltage fluctuation: 380V±10%
(3) Frequency: 50Hz
6. Has longitudinal step function
7. Operation table direction: Right to Left, face to the equipment.
u Key components schedule
No. | Name | Qty | Factory or nationality |
1 | Ac servo drive system | 1 | Taiwan DELTA |
2 | Servo motor | 1 | Taiwan DELTA |
3 | Motion controller | 8 | Taiwan CNC |
4 | Priority Encoder | 12 | Taiwan |
5 | Programmable controller | 1 | Taiwan |
6 | Control transformer | 7 | Japan |
7 | Miniature cylinder | 12 | Japan |
8 | position indicator | 2 | Germany SIKO |
9 | Main low voltage electric appliance | 1 | SCHNEIDER |
10 | Whole machine manufacture and installation | 1 | CANWIN |




